Laker

DESCRIPTION:

AT-LAKER is a solvent based, low sheen, crystal clear, deep penetrating coating for decorative concrete, stone, natural and manmade masonry surfaces. AT-LAKER provides a “damp-wet” appearance which enhances and beautifies the natural color of the applied masonry surface. Non yellowing AT-LAKER coating, seals against food stains, gasoline, grease, oils, water and acid. Its deep bonding formula resists peeling, chipping, cracking and UV degradation.

USES:

• Colored and stamped concrete
• Exposed aggregate concrete
• Interlocking pavers
• Mexican Tile
• Manufactured stone
• Masonry brick
• Natural stone
• Slate

ADVANTAGES:

• High gloss topical protective coating with rich look and enriches color
• Maximum protection against most stains
• Solvent-based
• Suitable for both interior and exterior use

USP:

• Resistant to oil and grease stains
• UV resistant bond, non yellowing
• Fast drying and long lasting
• Interior and exterior use
• Retards Efflorescence
• Excellent adhesion
• Water repellent
• Easy to apply
• Re-coatable

RECOMMENDED SURFACE FOR USAGE:

• Natural stone, masonry and decorative concrete (outdoor patios, walkways, driveways, garage floors, concrete slabs, sidewalks, retaining walls and BBQ areas)
• Not intended for use on dense, glazed, polished, or non-absorbing surfaces (ceramic tile, porcelain tile), wood floors and decks, showers, countertops, and near pool areas

COVERAGE & DRY TIME:

• Coverage varies based on porosity and texture of surface. Test advisable before application.
  • 1 kg coat will cover 125 sq.ft to 150sq.ft.

• Dry Time:
  • Touch Dry : 10-15 minutes

DIRECTION FOR USE:

• Always advisable to test in an inconspicuous area to determine desired results and also to ensure good adhesion. Surface must be thoroughly cleaned and dried before application. AT-LAKER should not be applied on wet or moist surface. Not recommended for areas with high moisture intrusion from surface below.
• Application to a dirty or dusty surface will affect adhesion.
• Allow newly cleaned surface to completely dry prior to applying AT-LAKER.
• Avoid applying in direct sunlight. Apply in air temperatures between 55–80ºF and on a cool, dry surface. Use only in well ventilated areas.
• While wearing an organic vapor respirator, liberally apply 2–4 even coats with a solvent-resistant natural bristle brush or roller. Failure to apply a sufficient amount of AT-LAKER to the surface may result in chipping or degradation of the coating. More coats may be applied if desired. Do not thin before using.
• Allow 1–3 hours between coats or until surface is dry to the touch.
• After application, do not walk on surface until AT-LAKER is completely cured. AT-LAKER will cure in 24–48 hours.
• Rags and equipment that are wet with product may be flammable. Clean up promptly after job is complete. Clean equipment with lacquer thinner and allow drying in a well-ventilated area. Allow rags to dry in a well-ventilated area out of the reach of children and pets. When dry, dispose of in accordance with local waste disposal regulations.
• AT-LAKER can be re-applied over existing coat of Lacquer to touch up scratches, bubbles, footprints, etc. No stripping is required. Finished surfaces may be slippery when wet.

TECHNICAL DATA SHEET:

PACKAGING & STORAGE:

• AT-LAKER is available in the following pack:
  • 20 kg HDPE container
• Shelf life is 36 months when stored in correct conditions. Shelf life is shortened once container is opened.
• Protect from frost. Store in clean, dry conditions between 5°C and 30°C.
• Stir material well before use

STORAGE & HANDLING INSTRUCTIONS:

• WARNING
  • FLAMMABLE – Keep away from heat, sparks and open flames. HARMFUL – IF SWALLOWED. Do not ingest. HARMFUL VAPORS. Avoid prolonged exposure to vapors. Use only in a well-ventilated area. Open all windows and doors to prevent vapor build-up. MAY CAUSE EYE, SKIN AND RESPIRATORY IRRITATION if used wrongly. Avoid contact with eyes and skin. Wear protective gloves, eyewear and a NIOSH approved organic vapor respirator when applying. KEEP OUT OF THE REACH OF CHILDREN. Do not store above 100°F/38°C. Do not mix with other chemicals.

• EMERGENCY / FIRST AID TIPS
  • INGESTION: Do not induce vomiting. Call poison control center. Call a Medical Practitioner if required.
  • EYE CONTACT: Flush thoroughly with water for at least 15 minutes. Remove contact lenses, if applicable, and continue flushing. Call a Medical Practitioner if required.
  • SKIN CONTACT: Wash skin thoroughly with mild soap and water. Call a physician if skin irritation persists. Launder affected clothing before re-wearing.
  • INHALATION: Remove to fresh air. Call a Medical Practitioner if irritation, nausea, dizziness or respiratory problems persist.

HEALTH & SAFETY:

• Protect hands with rubber gloves and eyes with goggles.
• Accidental splashes to the skin or eyes must be rinsed immediately with clean water.
• Store in well-labeled containers.