Coat(WT)767
DESCRIPTION:
AT–COAT (WT) 767 is a third generation epoxy resin based protective dispersion coating designed and formulated to meet the requirement of modern construction and ecological needs. AT–COAT (WT) 767 contains no solvents and as such is non-flammable, odour-less, water dilute-able, easily applied and is also an effective curing compound where subsequent coating is desired.
STANDARDS:
- AT-COAT (WT) 797 confirms to US- FDA 175.300, IS- 13239 – 1991, IS- 101(Part 6, Sec 3) – 1990
USES:
- AT – COAT (WT) 767 can be applied on concrete, rendering, stone, asbestos, cement etc.
- Ideal for cantilevers, galleries, retaining walls, basements, workshops, reservoirs, balconies etc. against weathering and mild chemical attack.
- It can be applied on concrete and surfaces which are still wet for curing of the concrete.
ADVANTAGES:
- AT – COAT (WT) 767 protects cementitious structures against weathering
- Resistant to oil and grease weather proof mildew resistant
- No solvent and as such no fire hazards
- Non-toxic with drinking water
- Suitable for portable water reservoirs
- Thixotropic no runs on vertical surfaces
- Easy to apply with brush or roller, adheres to damp surfaces also
- Odourless and acts as a curing compound
- Can be applied to concrete immediately after removing frame work
COVERAGE:
| COATING SYSTEM | PRODUCT | CONSUMPTION |
| PRIMER | AT-COAT (WT) 767 + 20 % water by weight | 0.1 – 0.2 kg/m2 |
| SEAL COAT | 2 – 3 x AT-COAT (WT) 767 | 0.15 – 0.25 kg/m2 per coat |
These figures are obtained under laboratory conditions and do not allow for any additional material due to surface porosity, surface profile, variations in level and wastage etc. Actual dosage depends on site trial.
APPLICATION:
- When mixed, it can be applied directly to the prepared surface by roller, spray or brush.
TECHNICAL DATA (typical values):
| COLOUR OF MIXED SYSTEM | White |
| DENSITY | Approximately 1.22 kg/ltr |
| MIXING RATIO | Component A : Component B = 1:1 by weight |
| POT LIFE | Approx 40 minutes at 30o C |
| APPLICATION TEMPERATURE | Minimum 10o C & Maximum 40o C |
| CURING TIME | Full cure 7 days at 30oC |
(All technical data stated herein is based on tests carried out under laboratory condition)
CHEMICAL RESISTANCE CHART:
| CHEMICAL REAGENT | OCCASSIONAL SPILLAGE | FREQUENT SPILLAGE | CONTINUOUS IMMERSION | ||
| Delonized Water | X | X | X | ||
| Methanol | X | X | |||
| Ethanol | X | X | |||
| Toluene | X | X | X | ||
| Xylene | X | X | X | ||
| Bufly Cellosolve | X | X | X | ||
| MEK | X | ||||
| 10% Lactic Acid | X | X | X | ||
| 10% Acedic Acid | X | X | |||
| 70% Sulfuric Acid | X | X | X | ||
| 98% Sulfuric Acid | X | X | X | ||
| 50% Sodium Hydroxide | X | X | X | ||
| 30% Sodium Hypochlorite | X | X | X | ||
| Trichloroethane | X | X | X | ||
| Hot Water (80º C) | X | X | |||
(All technical data stated herein is based on tests carried out under laboratory condition)
PACKAGING & STORAGE:
- AT-COAT (WT) 767 is available in the following system packing:
- Component A + Component B = 4 kg + 4 kg = 8 kg system pack (HDPE Container)
- Customize bigger packs on request only
- Shelf life is 12 months in sealed containers as provided
- Protect AT-COAT (WT) 767 from direct sunlight
- Keep containers sealed and away from heat and cold in a well ventilated area
- Stir material well before use
HEALTH & SAFETY:
- Protect hands with rubber gloves and eyes with goggles.
- Accidental splashes to the skin or eyes must be rinsed immediately with clean water or boric acid solution.
- Store in well-labeled containers.